Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）
A. The fabric interconnects must be in end-host mode.
B. A pin group must be configured on the server tab in Cisco UCS Manager.
C. In the service profile for Server 1， vNIC 1 must be explicitly assigned to a pin group.
D. Server 1 cannot be configured to meet the requirement. A server can only be manually pinned to a single physical interface and not a port channel because of the LACP load-balancing algorithm.
E. Server 1 cannot be configured to meet the requirement. A server is either manually pinned to an uplink on both fabric interconnects or the server is automatically pinned， but not both.
查看答案
Refer to the exhibit. The command spanning-tree guard root is configured on interface Gi0/0 on both switch S2 and S5. The global configuration command spanning-tree uplinkfast has been configured on both switch S2 and S5. The link between switch S4 and S5 fails. Will Host A be able to reach Host B？（）
A. Yes. Traffic can pass either from switch S6 to S3 to S2 to S1， or， from switch S6 to S5 to S2 to S1.
B. No. Traffic will pass from switch S6 to S5 and dead-end at interface Gi 0/0.
C. No. Traffic will loop back and forth between switch S5 and S2.
D. Yes. Traffic will pass from switch S6 to S3 to S2 to S1.
E. No. Traffic will either pass from switch S6 to S5 and dead-end， or traffic will pass from switch S6 to S3 to S2 and dead-end.
Which 4 statements regarding MPLS Label Stack Encoding is true？（）
A value of 4 represents the "Implicit NULL Label."
B. A value of 0 represents the "IPv4 Explicit NULL Label."
C. A value of 1 represents the "Router Alert Label". The use of this label is analogous to the use of the"Router Alert Option" in IP packets （for example， ping with record route option）
D. A value of 2 represents the "IPv6 Explicit NULL Label"
E. A value of 1 represents the "IPv1 Explicit NULL Label"
F. A value of 3 represents the "Implicit NULL Label"
Asingle802.11gaccesspointhasbeenconfiguredandinstalledinthecenterofasquareoffice.Afewwirelessusersareexperiencingslowperformanceanddropswhilemostusersareoperatingatpeakefficiency.Whatarethreelikelycausesofthisproblem?（）
A. mismatchedTKIPencryption
B. nullSSID
C. cordlessphones
D. mismatchedSSID
E. metalfilecabinets
F. antennatypeordirection
Refer to the exhibit. A Cisco Aironet Wireless LAN Client Adapter has been installed and configured through the ADU on the PC. The Aironet System Tray Utility （ASTU） has been enabled during the installation and the icon appears in the system tray area in the lower right of the desktop. What is the significance of the icon？（）
A. It indicates that the radio of the client adapter is disabled.
B. It indicates that the client adapter is not associated to an access point or another client.
C. It indicates that the client adapter is associated to an access point or another client， but the user is not EAP authenticated.
D. It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is excellent or good.
E. It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is fair.
F. It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is poor.
微信支付 
支付宝支付